.AixLib.Fluid.Interfaces.StaticTwoPortConservationEquation .AixLib.Fluid.Interfaces.StaticTwoPortConservationEquationThis model transports fluid between its two ports, without storing mass or energy. It implements a steady-state conservation equation for energy and mass fractions. The model has zero pressure drop between its ports.
Set the parameter use_mWat_flow_in=true to enable an
input connector for mWat_flow.
Otherwise, the model uses mWat_flow = 0.
If the constant simplify_mWat_flow = true, which is its default value,
then the equation
port_a.m_flow + port_b.m_flow = - mWat_flow;
is simplified as
port_a.m_flow + port_b.m_flow = 0;
This causes an error in the mass balance of about 0.5%, but generally leads to simpler equations because the pressure drop equations are then decoupled from the mass exchange in this component.
To increase the numerical robustness of the model, the constant
prescribedHeatFlowRate can be set.
Use the following settings:
prescribedHeatFlowRate=true if the only means of heat transfer
at the heatPort is a prescribed heat flow rate that
is not a function of the temperature difference
between the medium and an ambient temperature. Examples include an ideal electrical heater,
a pump that rejects heat into the fluid stream, or a chiller that removes heat based on a performance curve.
If the heatPort is not connected, then set prescribedHeatFlowRate=true as
in this case, heatPort.Q_flow=0.
prescribedHeatFlowRate=false if there is heat flow at the heatPort
computed as K * (T-heatPort.T), for some temperature T and some conductance K,
which may itself be a function of temperature or mass flow rate.prescribedHeatFlowRate=false.
If prescribedHeatFlow=true, then energy and mass balance
equations are formulated to guard against numerical problems near
zero flow that can occur if Q_flow or m_flow
are the results of an iterative solver.
Input connectors of the model are
Q_flow, which is the sensible plus latent heat flow rate added to the medium,
mWat_flow, which is the moisture mass flow rate added to the medium, and
C_flow, which is the trace substance mass flow rate added to the medium.
The model can only be used as a steady-state model with two fluid ports. For a model with a dynamic balance, and more fluid ports, use AixLib.Fluid.Interfaces.ConservationEquation.
XiOut.hOut as it will be set by
AixLib.Fluid.MixingVolumes.BaseClasses.PartialMixingVolume.TMax in assert.getInstanceName() in asserts to facilitate
debugging.regStep instead of spliceFunction.
This is for
#247
and for
#300.
mFlow_inv_b.
This is for
#247.
constant sensibleOnly as this is no longer used because
the model uses use_mWat_flow.m_flowInv needs to be
computed because the change from January 20 introduced an error in
AixLib.Fluid.MassExchangers.Examples.ConstantEffectiveness.
sensibleOnly
since this is no longer needed to simplify the equations.
This is for
#372.
use_C_flow and converted C_flow
to a conditionally removed connector.
This is for
#372.
C_flow to allow for PPM.
C_flow and code for handling trace substance insertions.
November 19, 2015, by Michael Wetter:showDesignFlowDirection in extends statement.
This is for
#349.
simplify_mWat_flow to remove dependencies of the pressure drop
calculation on the moisture balance.
port_a
if allowFlowReversal=false and
updated documentation.
See
issue 281 for a discussion.
prescribedHeatFlowRate
to MixingVolume instances.
Renamed use_safeDivision into prescribedHeatFlowRate.
See #282
for a discussion.
Q_flow input.
use_safeDivision=false
and sensibleOnly=true.
This only affects internal numerical tests, but not any examples in the library
as the constant use_safeDivision is set to true by default.
hOut.
i_w.
for loops for species balance and trace substance balance,
as they cause the error Error: Operand port_a.Xi_outflow[1] to operator inStream is not a stream variable.
in OpenModelica.
COut,
and added min and max attributes for XiOut.
m_flowInv to use port_a.m_flow * ...
if use_safeDivision=false. This avoids a division by zero if
port_a.m_flow=0.
AixLib.Fluid.Interfaces.
hOut, XiOut and
COut to no longer declare that it is continuous.
The declaration of continuity, i.e, the
smooth(0, if (port_a.m_flow >= 0) then ...) declaration,
was required for Dymola 2012 to simulate, but it is no longer needed
for Dymola 2012 FD01.
hOut, XiOut and
COut to declare that it is not differentiable.
m_flow=0.
homotopy operator.
port_b was multiplied with the mass flow rate at
port_a. The old implementation led to small errors that were proportional
to the amount of moisture change. For example, if the moisture added by the component
was 0.005 kg/kg, then the error was 0.5%.
Also, the results for forward flow and reverse flow differed by this amount.
With the new implementation, the energy and moisture balance is exact.
sensibleOnly to
simplify species balance equation.