modelFanger

Information

This model is based on the buildings library.

Thermal comfort model according to Fanger, as described in the ASHRAE Fundamentals (1997).

The thermal sensation of a human being is mainly related to the thermal balance of its body as a whole. This balance is influenced by two groups of factors, personal and physical. The activity level and clothing thermal insulation of the subject form the group of personal factors, while the environmental parameters: air temperature, mean radiant temperature, air velocity, and air humidity compose the group of physical factors. When the personal factors have been estimated and the physical factors have been measured the thermal sensation for the body as a whole (general thermal comfort) can be predicted by calculating the PMV index. The PPD index, obtained from the PMV index, provides information on thermal discomfort (thermal dissatisfaction) by predicting the percentage of people likely to feel too hot or too cold in the given thermal environment.

The Predicted Mean Vote (PMV) model combines four physical variables (air temperature, air velocity, mean radiant temperature, and relative humidity), and two personal variables (clothing insulation and activity level) into an index that can be used to predict the average thermal sensation of a large group of people.

To determine appropriate thermal conditions, practitioners refer to standards such as ASHRAE Standard 55 (ASHRAE, 1992) and ISO Standard 7730 (ISO, 1994). These standards define temperature ranges that should result in thermal satisfaction for at least 80% of occupants in a space.

PMV thermal sensation scale

The PMV index predicts the mean value of the votes of a large group of people on the following 7-point thermal sensation scale:

Operative temperature

For a given space there exists an optimum operative temperature corresponding to PMV=0 (neutral). The operative temperature is defined as: The uniform temperature of an imaginary black enclosure in which an occupant would exchange the same amount of heat by radiation plus convection as in the actual nonuniform environment. The operative temperature is computed as the average of the air temperature and the mean radiant temperature, weighted by their respective heat transfer coefficients (see ASHRAE Fundamentals, 1997, page 8.3, eq (8)).

Optimum operative temperatures

Winter: activity 1.2 met,
clothing = 0.9 clo (sweater, long sleeve shirt, heavy pants),
air flow = 30 fpm (0.15 m/sec),
mean radiant temperature equal to air temperature,
Optimum Operative Temperature (top) = 22.7° C (71° F)

Summer: clothing = 0.5 clo,
air flow = 50 fpm (0.25 m/sec),
Optimum Operative Temperature (top) = 24.4° C (76° F).

All equation numbers in the model refer to the ASHRAE Handbook Fundamentals, Chapter 8, Thermal Comfort, 1997.

Usual ranges of variables (ISO)

M = 46 to 232 W/m^2 (0.8 to 4 met)
ICl = 0 to 2 clo (0 to 0.310 m^2*K/W)
TAir_degC = 10 to 30° C
TRad_degC = 10 to 40° C
vAir = 0 to 1 m/s
pSte = 0 to 2700 Pa

Insulation for clothing ensembles

Clothing is defined in terms of clo units. Clo is a unit used to express the thermal insulation provided by garments and clothing ensembles, where 1 clo = 0.155 (m^2*K/W) (ASHRAE 55-92).

The following table is obtained from ASHRAE page 8.8

Metabolic rates

One met is defined as 58.2 Watts per square meter which is equal to the energy produced per unit surface area of a seated person at rest.

The following table is obtained from ASHRAE page 8.6.

References

• ASHRAE Handbook, Fundamentals (SI Edition). American Society of Heating, Refrigerating and Air-Conditioning Engineers, Chapter 8, Thermal Comfort; pages 8.1-8.26; Atlanta, USA, 1997.
• International Standards Organization (ISO). Moderate Thermal Environments: Determination of the PMV and PPD Indices and Specification of the Conditions for Thermal Comfort (ISO 7730). Geneva, Switzerland: ISO. 1994.
• Charles, K.E. Fanger Thermal Comfort and Draught Models. Institute for Research in Construction National Research Council of Canada, Ottawa, K1A 0R6, Canada. IRC Research Report RR-162. October 2003. http://irc.nrc-cnrc.gc.ca/ircpubs.
• Data, References and Links at: Thermal Comfort; Dr. Sam C M Hui Department of Mechanical Engineering The University of Hong Kong MEBS6006 Environmental Services I; http://me.hku.hk/msc-courses/MEBS6006/index.html

Parameters

Connectors

Components

Revisions

• April 11, 2019 by Filip Jorissen:
  Revised implementation such that default value of relative humidity is used when using a dry air medium. See #1011.
• Jul 18, 2016, by Filip Jorissen:
  Copied and changed implementation from Buildings library.
• May 30, 2014, by Michael Wetter:
  Removed undesirable annotation Evaluate=true. Added default value for ICl.
• October 9, 2013, by Michael Wetter:
  Corrected use of conditional connector.
• July 14, 2010, by Michael Wetter:
  Merged models into Buildings library. Fixed bug in computation of lower value for hCon. The original implementation lead to too high a lower value.
• August 2, 2005 Revised model, fixed bug in computing clothing surface temperature, changed various other computations, changed parameter and input to model, set clothing insulation value as input rather than computing it in model, added model to UTC library.
• June, 2005 Michael Wetter and Sorin Costiner:
  Improved version, added PPDDraft, TOpe, performed studies
• March 03, 2005 Michael Wetter and Sorin Costiner:
  First implementation.