Performance data for chiller model.
This data corresponds to the following EnergyPlus model:
Chiller:Electric:EIR,
ElectricEIRChiller Carrier 19XR 1076kW/5.52COP/Vanes, !- Name
1076100, !- Reference Capacity {W}
5.52, !- Reference COP {W/W}
5.56, !- Reference Leaving Chilled Water Temperature {C}
24.89, !- Reference Entering Condenser Fluid Temperature {C}
0.03186, !- Reference Chilled Water Flow Rate {m3/s}
0.04744, !- Reference Condenser Water Flow Rate {m3/s}
ElectricEIRChiller Carrier 19XR 1076kW/5.52COP/Vanes CAPFT, !- Cooling Capacity Function of Temperature Curve Name
ElectricEIRChiller Carrier 19XR 1076kW/5.52COP/Vanes EIRFT, !- Electric Input to Cooling Output Ratio Function of Temperature Curve Name
ElectricEIRChiller Carrier 19XR 1076kW/5.52COP/Vanes EIRFPLR, !- Electric Input to Cooling Output Ratio Function of Part Load Ratio Curve Name
0.10, !- Minimum Part Load Ratio
1.02, !- Maximum Part Load Ratio
1.0, !- Optimum Part Load Ratio
0.10, !- Minimum Unloading Ratio
Chilled Water Side Inlet Node, !- Chilled Water Inlet Node Name
Chilled Water Side Outlet Node, !- Chilled Water Outlet Node Name
Condenser Side Inlet Node, !- Condenser Inlet Node Name
Condenser Side Outlet Node, !- Condenser Outlet Node Name
WaterCooled, !- Condenser Type
, !- Condenser Fan Power Ratio {W/W}
1.0, !- Compressor Motor Efficiency
2.0, !- Leaving Chilled Water Lower Temperature Limit {C}
ConstantFlow, !- Chiller Flow Mode
0.0; !- Design Heat Recovery Water Flow Rate {m3/s}
record ElectricEIRChiller_Carrier_19XR_1076kW_5_52COP_Vanes = Buildings.Fluid.Chillers.Data.ElectricEIR.Generic(QEva_flow_nominal = -1076100, COP_nominal = 5.52, PLRMin = 0.10, PLRMinUnl = 0.10, PLRMax = 1.02, mEva_flow_nominal = 1000*0.03186, mCon_flow_nominal = 1000*0.04744, TEvaLvg_nominal = 273.15 + 5.56, TConEnt_nominal = 273.15 + 24.89, TEvaLvgMin = 273.15 + 5.56, TEvaLvgMax = 273.15 + 10.00, TConEntMin = 273.15 + 12.78, TConEntMax = 273.15 + 24.89, capFunT = {9.187704E-01, 4.509452E-02, -5.119187E-03, -2.095629E-04, -6.432511E-04, 2.791545E-03}, EIRFunT = {7.511044E-01, 2.415573E-02, -5.310959E-03, -1.073812E-03, 1.189538E-04, 1.604476E-03}, EIRFunPLR = {1.315760E-01, -3.004087E-02, 8.967180E-01}, etaMotor = 1.0);
Generated at 2024-12-28T19:26:00Z
by OpenModelicaOpenModelica 1.24.3 using GenerateDoc.mos