Performance data for chiller model.
This data corresponds to the following EnergyPlus model:
Chiller:Electric:EIR,
ElectricEIRChiller York YCAL0033EE 100.6kW/3.1COP, !- Name
100582, !- Reference Capacity {W}
3.1, !- Reference COP {W/W}
6.67, !- Reference Leaving Chilled Water Temperature {C}
35, !- Reference Entering Condenser Fluid Temperature {C}
0.0043, !- Reference Chilled Water Flow Rate {m3/s}
0.0011, !- Reference Condenser Fluid Flow Rate {m3/s}
ElectricEIRChiller York YCAL0033EE 100.6kW/3.1COP CAPFT, !- Cooling Capacity Function of Temperature Curve Name
ElectricEIRChiller York YCAL0033EE 100.6kW/3.1COP EIRFT, !- Electric Input to Cooling Output Ratio Function of Temperature Curve Name
ElectricEIRChiller York YCAL0033EE 100.6kW/3.1COP EIRFPLR, !- Electric Input to Cooling Output Ratio Function of Part Load Ratio Curve Name
0.10, !- Minimum Part Load Ratio
1.15, !- Maximum Part Load Ratio
1.0, !- Optimum Part Load Ratio
0.10, !- Minimum Unloading Ratio
Chilled Water Side Inlet Node, !- Chilled Water Inlet Node Name
Chilled Water Side Outlet Node, !- Chilled Water Outlet Node Name
Condenser Side Inlet Node, !- Condenser Inlet Node Name
Condenser Side Outlet Node, !- Condenser Outlet Node Name
AirCooled, !- Condenser Type
, !- Condenser Fan Power Ratio {W/W}
1.0, !- Fraction of Compressor Electric Consumption Rejected by Condenser
2.0, !- Leaving Chilled Water Lower Temperature Limit {C}
ConstantFlow, !- Chiller Flow Mode
0.0; !- Design Heat Recovery Water Flow Rate {m3/s}
Note that the reference condenser fluid volumetric flow rate listed in the
EnergyPlus performance data is not reasonable. The value obtained
from the manufacturer data sheet is used instead. The data sheet
is available
here
. Please see the Section for Physical Data and Nominal Ratings and row for Condender Fans Total Chiller CFM.
record ElectricEIRChiller_York_YCAL0033EE_101kW_3_1COP_AirCooled = Buildings.Fluid.Chillers.Data.ElectricEIR.Generic(QEva_flow_nominal = -100582, COP_nominal = 3.1, PLRMin = 0.10, PLRMinUnl = 0.10, PLRMax = 1.15, mEva_flow_nominal = 1000*0.0043, mCon_flow_nominal = 1.2*9.4389, TEvaLvg_nominal = 273.15 + 6.67, TConEnt_nominal = 273.15 + 35, TEvaLvgMin = 273.15 + 4.44, TEvaLvgMax = 273.15 + 10.0, TConEntMin = 273.15 + 23.89, TConEntMax = 273.15 + 51.67, capFunT = {-0.2660645697, 0.0998714035, -0.0023814154, 0.0628316481, -0.0009644649, -0.0011249224}, EIRFunT = {0.1807017787, 0.0271530312, -0.0004553574, 0.0188175079, 0.0002623276, -0.0012881189}, EIRFunPLR = {0.0, 1.0, 0.0}, etaMotor = 1.0);
Generated at 2024-11-22T19:25:38Z
by OpenModelicaOpenModelica 1.24.2 using GenerateDoc.mos