Performance data for chiller model.
This data corresponds to the following EnergyPlus model:
Chiller:Electric:ReformulatedEIR,
ReformEIRChiller York YK 2159kW/6.85COP/Vanes, !- Name
2159200, !- Reference Capacity {W}
6.85, !- Reference COP {W/W}
6.67, !- Reference Leaving Chilled Water Temperature {C}
31.32, !- Reference Leaving Condenser Water Temperature {C}
0.07571, !- Reference Chilled Water Flow Rate {m3/s}
0.11356, !- Reference Condenser Water Flow Rate {m3/s}
ReformEIRChiller York YK 2159kW/6.85COP/Vanes CAPFT, !- Cooling Capacity Function of Temperature Curve Name
ReformEIRChiller York YK 2159kW/6.85COP/Vanes EIRFT, !- Electric Input to Cooling Output Ratio Function of Temperature Curve Name
ReformEIRChiller York YK 2159kW/6.85COP/Vanes EIRFPLR, !- Electric Input to Cooling Output Ratio Function of Part Load Ratio Curve Name
0.14, !- Minimum Part Load Ratio
1.05, !- Maximum Part Load Ratio
1.0, !- Optimum Part Load Ratio
0.14, !- Minimum Unloading Ratio
Chilled Water Side Inlet Node, !- Chilled Water Inlet Node Name
Chilled Water Side Outlet Node, !- Chilled Water Outlet Node Name
Condenser Side Inlet Node, !- Condenser Inlet Node Name
Condenser Side Outlet Node, !- Condenser Outlet Node Name
1.0, !- Compressor Motor Efficiency
2.0, !- Leaving Chilled Water Lower Temperature Limit {C}
ConstantFlow, !- Chiller Flow Mode Type
0.0; !- Design Heat Recovery Water Flow Rate {m3/s}
record ReformEIRChiller_York_YK_2159kW_6_85COP_Vanes = Buildings.Fluid.Chillers.Data.ElectricReformulatedEIR.Generic(QEva_flow_nominal = -2159200, COP_nominal = 6.85, PLRMin = 0.14, PLRMinUnl = 0.14, PLRMax = 1.05, mEva_flow_nominal = 1000*0.07571, mCon_flow_nominal = 1000*0.11356, TEvaLvg_nominal = 273.15 + 6.67, TConLvg_nominal = 273.15 + 31.32, TEvaLvgMin = 273.15 + 4.44, TEvaLvgMax = 273.15 + 8.89, TConLvgMin = 273.15 + 21.13, TConLvgMax = 273.15 + 34.75, capFunT = {-5.164056E-02, -7.384855E-02, -1.036241E-02, 1.201446E-01, -3.881099E-03, 9.873049E-03}, EIRFunT = {1.013059E+00, 2.176325E-03, -4.682395E-04, -1.887683E-02, 7.444727E-04, -6.685547E-04}, EIRFunPLR = {2.315688E-02, 2.746250E-02, -2.345600E-05, -4.728932E-01, 1.778530E+00, -2.621741E-02, 0.000000E+00, -3.448533E-01, 0.000000E+00, 0.000000E+00}, etaMotor = 1.0);
Generated at 2024-11-22T19:25:38Z
by OpenModelicaOpenModelica 1.24.2 using GenerateDoc.mos