Performance data for chiller model.
This data corresponds to the following EnergyPlus model:
Chiller:Electric:ReformulatedEIR,
ReformEIRChiller York YK 2237kW/6.41COP/Vanes, !- Name
2236600, !- Reference Capacity {W}
6.41, !- Reference COP {W/W}
6.67, !- Reference Leaving Chilled Water Temperature {C}
31.56, !- Reference Leaving Condenser Water Temperature {C}
0.07571, !- Reference Chilled Water Flow Rate {m3/s}
0.11356, !- Reference Condenser Water Flow Rate {m3/s}
ReformEIRChiller York YK 2237kW/6.41COP/Vanes CAPFT, !- Cooling Capacity Function of Temperature Curve Name
ReformEIRChiller York YK 2237kW/6.41COP/Vanes EIRFT, !- Electric Input to Cooling Output Ratio Function of Temperature Curve Name
ReformEIRChiller York YK 2237kW/6.41COP/Vanes EIRFPLR, !- Electric Input to Cooling Output Ratio Function of Part Load Ratio Curve Name
0.13, !- Minimum Part Load Ratio
1.02, !- Maximum Part Load Ratio
1.0, !- Optimum Part Load Ratio
0.13, !- Minimum Unloading Ratio
Chilled Water Side Inlet Node, !- Chilled Water Inlet Node Name
Chilled Water Side Outlet Node, !- Chilled Water Outlet Node Name
Condenser Side Inlet Node, !- Condenser Inlet Node Name
Condenser Side Outlet Node, !- Condenser Outlet Node Name
1.0, !- Compressor Motor Efficiency
2.0, !- Leaving Chilled Water Lower Temperature Limit {C}
ConstantFlow, !- Chiller Flow Mode Type
0.0; !- Design Heat Recovery Water Flow Rate {m3/s}
record ReformEIRChiller_York_YK_2237kW_6_41COP_Vanes = Buildings.Fluid.Chillers.Data.ElectricReformulatedEIR.Generic(QEva_flow_nominal = -2236600, COP_nominal = 6.41, PLRMin = 0.13, PLRMinUnl = 0.13, PLRMax = 1.02, mEva_flow_nominal = 1000*0.07571, mCon_flow_nominal = 1000*0.11356, TEvaLvg_nominal = 273.15 + 6.67, TConLvg_nominal = 273.15 + 31.56, TEvaLvgMin = 273.15 + 4.44, TEvaLvgMax = 273.15 + 8.89, TConLvgMin = 273.15 + 21.30, TConLvgMax = 273.15 + 35.03, capFunT = {2.686272E-01, -4.051077E-02, -2.130203E-03, 7.674578E-02, -2.282522E-03, 4.478325E-03}, EIRFunT = {9.801548E-01, 2.026687E-02, 1.578707E-03, -2.077442E-02, 9.180399E-04, -2.105614E-03}, EIRFunPLR = {2.013555E-01, 1.055744E-02, -2.587525E-05, -3.074339E-01, 1.634011E+00, -9.188562E-03, 0.000000E+00, -5.458636E-01, 0.000000E+00, 0.000000E+00}, etaMotor = 1.0);
Generated at 2024-12-28T19:26:00Z
by OpenModelicaOpenModelica 1.24.3 using GenerateDoc.mos