Performance data for chiller model.
This data corresponds to the following EnergyPlus model:
Chiller:Electric:ReformulatedEIR,
ReformEIRChiller York YK 4477kW/6.64COP/Vanes, !- Name
4476700, !- Reference Capacity {W}
6.64, !- Reference COP {W/W}
6.67, !- Reference Leaving Chilled Water Temperature {C}
31.67, !- Reference Leaving Condenser Water Temperature {C}
0.19558, !- Reference Chilled Water Flow Rate {m3/s}
0.24605, !- Reference Condenser Water Flow Rate {m3/s}
ReformEIRChiller York YK 4477kW/6.64COP/Vanes CAPFT, !- Cooling Capacity Function of Temperature Curve Name
ReformEIRChiller York YK 4477kW/6.64COP/Vanes EIRFT, !- Electric Input to Cooling Output Ratio Function of Temperature Curve Name
ReformEIRChiller York YK 4477kW/6.64COP/Vanes EIRFPLR, !- Electric Input to Cooling Output Ratio Function of Part Load Ratio Curve Name
0.41, !- Minimum Part Load Ratio
1.06, !- Maximum Part Load Ratio
1.0, !- Optimum Part Load Ratio
0.41, !- Minimum Unloading Ratio
Chilled Water Side Inlet Node, !- Chilled Water Inlet Node Name
Chilled Water Side Outlet Node, !- Chilled Water Outlet Node Name
Condenser Side Inlet Node, !- Condenser Inlet Node Name
Condenser Side Outlet Node, !- Condenser Outlet Node Name
1.0, !- Compressor Motor Efficiency
2.0, !- Leaving Chilled Water Lower Temperature Limit {C}
ConstantFlow, !- Chiller Flow Mode Type
0.0; !- Design Heat Recovery Water Flow Rate {m3/s}
record ReformEIRChiller_York_YK_4477kW_6_64COP_Vanes = Buildings.Fluid.Chillers.Data.ElectricReformulatedEIR.Generic(QEva_flow_nominal = -4476700, COP_nominal = 6.64, PLRMin = 0.41, PLRMinUnl = 0.41, PLRMax = 1.06, mEva_flow_nominal = 1000*0.19558, mCon_flow_nominal = 1000*0.24605, TEvaLvg_nominal = 273.15 + 6.67, TConLvg_nominal = 273.15 + 31.67, TEvaLvgMin = 273.15 + 4.44, TEvaLvgMax = 273.15 + 7.78, TConLvgMin = 273.15 + 18.50, TConLvgMax = 273.15 + 31.67, capFunT = {-5.612561E-01, -2.094117E-01, -8.555483E-03, 2.050690E-01, -6.451488E-03, 1.561052E-02}, EIRFunT = {1.597687E-01, -3.513678E-02, -2.666547E-03, 5.561175E-02, -9.273482E-04, 1.559350E-03}, EIRFunPLR = {6.263474E-01, -1.468760E-02, 2.187947E-04, -4.940077E-01, 1.448597E+00, 4.085582E-03, 0.000000E+00, -4.576722E-01, 0.000000E+00, 0.000000E+00}, etaMotor = 1.0);
Generated at 2024-11-22T19:25:38Z
by OpenModelicaOpenModelica 1.24.2 using GenerateDoc.mos