Performance data for chiller model.
This data corresponds to the following EnergyPlus model:
Chiller:Electric:ReformulatedEIR,
ReformEIRChiller York YK 4537kW/6.28COP/Vanes, !- Name
4536500, !- Reference Capacity {W}
6.28, !- Reference COP {W/W}
6.67, !- Reference Leaving Chilled Water Temperature {C}
31.78, !- Reference Leaving Condenser Water Temperature {C}
0.19558, !- Reference Chilled Water Flow Rate {m3/s}
0.24605, !- Reference Condenser Water Flow Rate {m3/s}
ReformEIRChiller York YK 4537kW/6.28COP/Vanes CAPFT, !- Cooling Capacity Function of Temperature Curve Name
ReformEIRChiller York YK 4537kW/6.28COP/Vanes EIRFT, !- Electric Input to Cooling Output Ratio Function of Temperature Curve Name
ReformEIRChiller York YK 4537kW/6.28COP/Vanes EIRFPLR, !- Electric Input to Cooling Output Ratio Function of Part Load Ratio Curve Name
0.40, !- Minimum Part Load Ratio
1.04, !- Maximum Part Load Ratio
1.0, !- Optimum Part Load Ratio
0.40, !- Minimum Unloading Ratio
Chilled Water Side Inlet Node, !- Chilled Water Inlet Node Name
Chilled Water Side Outlet Node, !- Chilled Water Outlet Node Name
Condenser Side Inlet Node, !- Condenser Inlet Node Name
Condenser Side Outlet Node, !- Condenser Outlet Node Name
1.0, !- Compressor Motor Efficiency
2.0, !- Leaving Chilled Water Lower Temperature Limit {C}
ConstantFlow, !- Chiller Flow Mode Type
0.0; !- Design Heat Recovery Water Flow Rate {m3/s}
record ReformEIRChiller_York_YK_4537kW_6_28COP_Vanes = Buildings.Fluid.Chillers.Data.ElectricReformulatedEIR.Generic(QEva_flow_nominal = -4536500, COP_nominal = 6.28, PLRMin = 0.40, PLRMinUnl = 0.40, PLRMax = 1.04, mEva_flow_nominal = 1000*0.19558, mCon_flow_nominal = 1000*0.24605, TEvaLvg_nominal = 273.15 + 6.67, TConLvg_nominal = 273.15 + 31.78, TEvaLvgMin = 273.15 + 4.44, TEvaLvgMax = 273.15 + 7.78, TConLvgMin = 273.15 + 19.77, TConLvgMax = 273.15 + 31.78, capFunT = {1.769339E-01, 8.033367E-04, -1.299649E-02, 1.160227E-01, -4.192731E-03, 9.339837E-03}, EIRFunT = {8.920183E-01, -1.501518E-02, 1.467430E-03, -1.261335E-02, 8.431355E-04, -1.426299E-03}, EIRFunPLR = {1.718938E-01, 6.637990E-03, 1.666991E-05, 1.634153E-01, 9.517270E-01, -7.705773E-03, 0.000000E+00, -2.724674E-01, 0.000000E+00, 0.000000E+00}, etaMotor = 1.0);
Generated at 2024-12-28T19:26:00Z
by OpenModelicaOpenModelica 1.24.3 using GenerateDoc.mos