Performance data for chiller model.
This data corresponds to the following EnergyPlus model:
Chiller:Electric:ReformulatedEIR,
ReformEIRChiller York YK 4966kW/6.05COP/Vanes, !- Name
4965500, !- Reference Capacity {W}
6.05, !- Reference COP {W/W}
6.67, !- Reference Leaving Chilled Water Temperature {C}
31.33, !- Reference Leaving Condenser Water Temperature {C}
0.21198, !- Reference Chilled Water Flow Rate {m3/s}
0.26498, !- Reference Condenser Water Flow Rate {m3/s}
ReformEIRChiller York YK 4966kW/6.05COP/Vanes CAPFT, !- Cooling Capacity Function of Temperature Curve Name
ReformEIRChiller York YK 4966kW/6.05COP/Vanes EIRFT, !- Electric Input to Cooling Output Ratio Function of Temperature Curve Name
ReformEIRChiller York YK 4966kW/6.05COP/Vanes EIRFPLR, !- Electric Input to Cooling Output Ratio Function of Part Load Ratio Curve Name
0.12, !- Minimum Part Load Ratio
1.02, !- Maximum Part Load Ratio
1.0, !- Optimum Part Load Ratio
0.12, !- Minimum Unloading Ratio
Chilled Water Side Inlet Node, !- Chilled Water Inlet Node Name
Chilled Water Side Outlet Node, !- Chilled Water Outlet Node Name
Condenser Side Inlet Node, !- Condenser Inlet Node Name
Condenser Side Outlet Node, !- Condenser Outlet Node Name
1.0, !- Compressor Motor Efficiency
2.0, !- Leaving Chilled Water Lower Temperature Limit {C}
ConstantFlow, !- Chiller Flow Mode Type
0.0; !- Design Heat Recovery Water Flow Rate {m3/s}
record ReformEIRChiller_York_YK_4966kW_6_05COP_Vanes = Buildings.Fluid.Chillers.Data.ElectricReformulatedEIR.Generic(QEva_flow_nominal = -4965500, COP_nominal = 6.05, PLRMin = 0.12, PLRMinUnl = 0.12, PLRMax = 1.02, mEva_flow_nominal = 1000*0.21198, mCon_flow_nominal = 1000*0.26498, TEvaLvg_nominal = 273.15 + 6.67, TConLvg_nominal = 273.15 + 31.33, TEvaLvgMin = 273.15 + 4.44, TEvaLvgMax = 273.15 + 8.89, TConLvgMin = 273.15 + 20.07, TConLvgMax = 273.15 + 35.01, capFunT = {4.672989E-01, -3.881077E-02, -2.462607E-04, 3.605453E-02, -8.010103E-04, 2.190852E-03}, EIRFunT = {8.536699E-01, 3.487393E-04, 1.120994E-03, -9.358730E-03, 6.197745E-04, -1.128239E-03}, EIRFunPLR = {2.620385E-01, 1.209698E-02, 8.014586E-06, -1.102167E-01, 1.117062E+00, -1.249449E-02, 0.000000E+00, -2.641246E-01, 0.000000E+00, 0.000000E+00}, etaMotor = 1.0);
Generated at 2024-12-28T19:26:00Z
by OpenModelicaOpenModelica 1.24.3 using GenerateDoc.mos