Performance data for chiller model.
This data corresponds to the following EnergyPlus model:
Chiller:Electric:ReformulatedEIR,
ReformEIRChiller York YK 4969kW/7.07COP/Vanes, !- Name
4969000, !- Reference Capacity {W}
7.07, !- Reference COP {W/W}
6.67, !- Reference Leaving Chilled Water Temperature {C}
31.23, !- Reference Leaving Condenser Water Temperature {C}
0.17665, !- Reference Chilled Water Flow Rate {m3/s}
0.26498, !- Reference Condenser Water Flow Rate {m3/s}
ReformEIRChiller York YK 4969kW/7.07COP/Vanes CAPFT, !- Cooling Capacity Function of Temperature Curve Name
ReformEIRChiller York YK 4969kW/7.07COP/Vanes EIRFT, !- Electric Input to Cooling Output Ratio Function of Temperature Curve Name
ReformEIRChiller York YK 4969kW/7.07COP/Vanes EIRFPLR, !- Electric Input to Cooling Output Ratio Function of Part Load Ratio Curve Name
0.16, !- Minimum Part Load Ratio
1.05, !- Maximum Part Load Ratio
1.0, !- Optimum Part Load Ratio
0.16, !- Minimum Unloading Ratio
Chilled Water Side Inlet Node, !- Chilled Water Inlet Node Name
Chilled Water Side Outlet Node, !- Chilled Water Outlet Node Name
Condenser Side Inlet Node, !- Condenser Inlet Node Name
Condenser Side Outlet Node, !- Condenser Outlet Node Name
1.0, !- Compressor Motor Efficiency
2.0, !- Leaving Chilled Water Lower Temperature Limit {C}
ConstantFlow, !- Chiller Flow Mode Type
0.0; !- Design Heat Recovery Water Flow Rate {m3/s}
record ReformEIRChiller_York_YK_4969kW_7_07COP_Vanes = Buildings.Fluid.Chillers.Data.ElectricReformulatedEIR.Generic(QEva_flow_nominal = -4969000, COP_nominal = 7.07, PLRMin = 0.16, PLRMinUnl = 0.16, PLRMax = 1.05, mEva_flow_nominal = 1000*0.17665, mCon_flow_nominal = 1000*0.26498, TEvaLvg_nominal = 273.15 + 6.67, TConLvg_nominal = 273.15 + 31.23, TEvaLvgMin = 273.15 + 4.44, TEvaLvgMax = 273.15 + 8.89, TConLvgMin = 273.15 + 21.30, TConLvgMax = 273.15 + 34.56, capFunT = {-1.238406E+00, -2.167075E-01, -9.525838E-03, 2.481491E-01, -6.930334E-03, 1.495974E-02}, EIRFunT = {7.217115E-01, -3.596981E-02, 5.327502E-04, 9.190024E-03, 1.694811E-04, 1.843438E-04}, EIRFunPLR = {7.117270E-01, 1.022191E-03, 1.205226E-05, -1.794131E+00, 3.295736E+00, -1.552001E-03, 0.000000E+00, -1.207188E+00, 0.000000E+00, 0.000000E+00}, etaMotor = 1.0);
Generated at 2024-11-22T19:25:38Z
by OpenModelicaOpenModelica 1.24.2 using GenerateDoc.mos