Performance data for chiller model.
This data corresponds to the following EnergyPlus model:
Chiller:Electric:ReformulatedEIR,
ReformEIRChiller York YK 5170kW/7.15COP/Vanes, !- Name
5169500, !- Reference Capacity {W}
7.15, !- Reference COP {W/W}
6.67, !- Reference Leaving Chilled Water Temperature {C}
31.43, !- Reference Leaving Condenser Water Temperature {C}
0.17665, !- Reference Chilled Water Flow Rate {m3/s}
0.26498, !- Reference Condenser Water Flow Rate {m3/s}
ReformEIRChiller York YK 5170kW/7.15COP/Vanes CAPFT, !- Cooling Capacity Function of Temperature Curve Name
ReformEIRChiller York YK 5170kW/7.15COP/Vanes EIRFT, !- Electric Input to Cooling Output Ratio Function of Temperature Curve Name
ReformEIRChiller York YK 5170kW/7.15COP/Vanes EIRFPLR, !- Electric Input to Cooling Output Ratio Function of Part Load Ratio Curve Name
0.15, !- Minimum Part Load Ratio
1.07, !- Maximum Part Load Ratio
1.0, !- Optimum Part Load Ratio
0.15, !- Minimum Unloading Ratio
Chilled Water Side Inlet Node, !- Chilled Water Inlet Node Name
Chilled Water Side Outlet Node, !- Chilled Water Outlet Node Name
Condenser Side Inlet Node, !- Condenser Inlet Node Name
Condenser Side Outlet Node, !- Condenser Outlet Node Name
1.0, !- Compressor Motor Efficiency
2.0, !- Leaving Chilled Water Lower Temperature Limit {C}
ConstantFlow, !- Chiller Flow Mode Type
0.0; !- Design Heat Recovery Water Flow Rate {m3/s}
record ReformEIRChiller_York_YK_5170kW_7_15COP_Vanes = Buildings.Fluid.Chillers.Data.ElectricReformulatedEIR.Generic(QEva_flow_nominal = -5169500, COP_nominal = 7.15, PLRMin = 0.15, PLRMinUnl = 0.15, PLRMax = 1.07, mEva_flow_nominal = 1000*0.17665, mCon_flow_nominal = 1000*0.26498, TEvaLvg_nominal = 273.15 + 6.67, TConLvg_nominal = 273.15 + 31.43, TEvaLvgMin = 273.15 + 4.44, TEvaLvgMax = 273.15 + 8.89, TConLvgMin = 273.15 + 21.30, TConLvgMax = 273.15 + 34.88, capFunT = {-1.064004E+00, -2.233223E-01, -7.441205E-03, 2.281866E-01, -6.268922E-03, 1.390983E-02}, EIRFunT = {5.056958E-01, -2.296962E-02, -1.632795E-03, 2.230325E-02, -1.548393E-04, 8.256108E-04}, EIRFunPLR = {7.949169E-01, 9.107817E-04, 3.483284E-05, -2.015044E+00, 3.394622E+00, -2.646463E-03, 0.000000E+00, -1.152785E+00, 0.000000E+00, 0.000000E+00}, etaMotor = 1.0);
Generated at 2024-12-28T19:26:00Z
by OpenModelicaOpenModelica 1.24.3 using GenerateDoc.mos