Performance data for chiller model.
This data corresponds to the following EnergyPlus model:
Chiller:Electric:ReformulatedEIR,
ReformEIRChiller York YK 5465kW/6.94COP/Vanes, !- Name
5464900, !- Reference Capacity {W}
6.94, !- Reference COP {W/W}
6.67, !- Reference Leaving Chilled Water Temperature {C}
31.56, !- Reference Leaving Condenser Water Temperature {C}
0.18296, !- Reference Chilled Water Flow Rate {m3/s}
0.27444, !- Reference Condenser Water Flow Rate {m3/s}
ReformEIRChiller York YK 5465kW/6.94COP/Vanes CAPFT, !- Cooling Capacity Function of Temperature Curve Name
ReformEIRChiller York YK 5465kW/6.94COP/Vanes EIRFT, !- Electric Input to Cooling Output Ratio Function of Temperature Curve Name
ReformEIRChiller York YK 5465kW/6.94COP/Vanes EIRFPLR, !- Electric Input to Cooling Output Ratio Function of Part Load Ratio Curve Name
0.14, !- Minimum Part Load Ratio
1.06, !- Maximum Part Load Ratio
1.0, !- Optimum Part Load Ratio
0.14, !- Minimum Unloading Ratio
Chilled Water Side Inlet Node, !- Chilled Water Inlet Node Name
Chilled Water Side Outlet Node, !- Chilled Water Outlet Node Name
Condenser Side Inlet Node, !- Condenser Inlet Node Name
Condenser Side Outlet Node, !- Condenser Outlet Node Name
1.0, !- Compressor Motor Efficiency
2.0, !- Leaving Chilled Water Lower Temperature Limit {C}
ConstantFlow, !- Chiller Flow Mode Type
0.0; !- Design Heat Recovery Water Flow Rate {m3/s}
record ReformEIRChiller_York_YK_5465kW_6_94COP_Vanes = Buildings.Fluid.Chillers.Data.ElectricReformulatedEIR.Generic(QEva_flow_nominal = -5464900, COP_nominal = 6.94, PLRMin = 0.14, PLRMinUnl = 0.14, PLRMax = 1.06, mEva_flow_nominal = 1000*0.18296, mCon_flow_nominal = 1000*0.27444, TEvaLvg_nominal = 273.15 + 6.67, TConLvg_nominal = 273.15 + 31.56, TEvaLvgMin = 273.15 + 4.44, TEvaLvgMax = 273.15 + 8.89, TConLvgMin = 273.15 + 21.03, TConLvgMax = 273.15 + 34.99, capFunT = {-1.004987E+00, -2.020843E-01, -5.768143E-03, 2.096972E-01, -5.537991E-03, 1.195948E-02}, EIRFunT = {5.844853E-01, -4.786810E-02, 7.315110E-04, 2.167930E-02, -8.850313E-05, 5.184829E-04}, EIRFunPLR = {8.903067E-01, -1.058205E-03, 4.591261E-05, -2.096863E+00, 3.368956E+00, -1.380690E-03, 0.000000E+00, -1.130250E+00, 0.000000E+00, 0.000000E+00}, etaMotor = 1.0);
Generated at 2024-12-28T19:26:00Z
by OpenModelicaOpenModelica 1.24.3 using GenerateDoc.mos