Performance data for chiller model.
This data corresponds to the following EnergyPlus model:
Chiller:Electric:ReformulatedEIR,
ReformEIRChiller York YK 5549kW/6.50COP/Vanes, !- Name
5549300, !- Reference Capacity {W}
6.50, !- Reference COP {W/W}
6.67, !- Reference Leaving Chilled Water Temperature {C}
31.69, !- Reference Leaving Condenser Water Temperature {C}
0.18296, !- Reference Chilled Water Flow Rate {m3/s}
0.27444, !- Reference Condenser Water Flow Rate {m3/s}
ReformEIRChiller York YK 5549kW/6.50COP/Vanes CAPFT, !- Cooling Capacity Function of Temperature Curve Name
ReformEIRChiller York YK 5549kW/6.50COP/Vanes EIRFT, !- Electric Input to Cooling Output Ratio Function of Temperature Curve Name
ReformEIRChiller York YK 5549kW/6.50COP/Vanes EIRFPLR, !- Electric Input to Cooling Output Ratio Function of Part Load Ratio Curve Name
0.14, !- Minimum Part Load Ratio
1.05, !- Maximum Part Load Ratio
1.0, !- Optimum Part Load Ratio
0.14, !- Minimum Unloading Ratio
Chilled Water Side Inlet Node, !- Chilled Water Inlet Node Name
Chilled Water Side Outlet Node, !- Chilled Water Outlet Node Name
Condenser Side Inlet Node, !- Condenser Inlet Node Name
Condenser Side Outlet Node, !- Condenser Outlet Node Name
1.0, !- Compressor Motor Efficiency
2.0, !- Leaving Chilled Water Lower Temperature Limit {C}
ConstantFlow, !- Chiller Flow Mode Type
0.0; !- Design Heat Recovery Water Flow Rate {m3/s}
record ReformEIRChiller_York_YK_5549kW_6_50COP_Vanes = Buildings.Fluid.Chillers.Data.ElectricReformulatedEIR.Generic(QEva_flow_nominal = -5549300, COP_nominal = 6.50, PLRMin = 0.14, PLRMinUnl = 0.14, PLRMax = 1.05, mEva_flow_nominal = 1000*0.18296, mCon_flow_nominal = 1000*0.27444, TEvaLvg_nominal = 273.15 + 6.67, TConLvg_nominal = 273.15 + 31.69, TEvaLvgMin = 273.15 + 4.44, TEvaLvgMax = 273.15 + 8.89, TConLvgMin = 273.15 + 18.38, TConLvgMax = 273.15 + 31.70, capFunT = {-8.620027E-01, 6.692796E-03, -4.020156E-03, 1.550060E-01, -3.586968E-03, 3.027128E-03}, EIRFunT = {3.302868E-01, -8.254126E-02, 6.087519E-03, 4.875213E-02, -5.839053E-04, -5.006909E-05}, EIRFunPLR = {5.179058E-01, -2.419877E-03, 4.858626E-05, -8.910290E-01, 2.272953E+00, -3.062303E-04, 0.000000E+00, -8.631289E-01, 0.000000E+00, 0.000000E+00}, etaMotor = 1.0);
Generated at 2024-12-28T19:26:00Z
by OpenModelicaOpenModelica 1.24.3 using GenerateDoc.mos