Performance data for chiller model.
This data corresponds to the following EnergyPlus model:
Chiller:Electric:ReformulatedEIR,
ReformEIRChiller York YT 1048kW/6.06COP/Vanes, !- Name
1047900, !- Reference Capacity {W}
6.06, !- Reference COP {W/W}
6.67, !- Reference Leaving Chilled Water Temperature {C}
34.59, !- Reference Leaving Condenser Water Temperature {C}
0.04542, !- Reference Chilled Water Flow Rate {m3/s}
0.05678, !- Reference Condenser Water Flow Rate {m3/s}
ReformEIRChiller York YT 1048kW/6.06COP/Vanes CAPFT, !- Cooling Capacity Function of Temperature Curve Name
ReformEIRChiller York YT 1048kW/6.06COP/Vanes EIRFT, !- Electric Input to Cooling Output Ratio Function of Temperature Curve Name
ReformEIRChiller York YT 1048kW/6.06COP/Vanes EIRFPLR, !- Electric Input to Cooling Output Ratio Function of Part Load Ratio Curve Name
0.10, !- Minimum Part Load Ratio
1.06, !- Maximum Part Load Ratio
1.0, !- Optimum Part Load Ratio
0.10, !- Minimum Unloading Ratio
Chilled Water Side Inlet Node, !- Chilled Water Inlet Node Name
Chilled Water Side Outlet Node, !- Chilled Water Outlet Node Name
Condenser Side Inlet Node, !- Condenser Inlet Node Name
Condenser Side Outlet Node, !- Condenser Outlet Node Name
1.0, !- Compressor Motor Efficiency
2.0, !- Leaving Chilled Water Lower Temperature Limit {C}
ConstantFlow, !- Chiller Flow Mode Type
0.0; !- Design Heat Recovery Water Flow Rate {m3/s}
record ReformEIRChiller_York_YT_1048kW_6_06COP_Vanes = Buildings.Fluid.Chillers.Data.ElectricReformulatedEIR.Generic(QEva_flow_nominal = -1047900, COP_nominal = 6.06, PLRMin = 0.10, PLRMinUnl = 0.10, PLRMax = 1.06, mEva_flow_nominal = 1000*0.04542, mCon_flow_nominal = 1000*0.05678, TEvaLvg_nominal = 273.15 + 6.67, TConLvg_nominal = 273.15 + 34.59, TEvaLvgMin = 273.15 + 4.44, TEvaLvgMax = 273.15 + 8.89, TConLvgMin = 273.15 + 20.43, TConLvgMax = 273.15 + 39.72, capFunT = {5.846663E-01, 1.059863E-02, -5.058695E-03, 3.006085E-02, -9.364366E-04, 2.597223E-03}, EIRFunT = {7.745270E-01, -3.256346E-02, 2.992117E-03, -5.274460E-03, 6.701377E-04, -1.236258E-03}, EIRFunPLR = {5.753623E-01, -1.409335E-02, -5.983885E-06, 6.063425E-01, -3.090569E-01, 1.412467E-02, 0.000000E+00, 1.296066E-01, 0.000000E+00, 0.000000E+00}, etaMotor = 1.0);
Generated at 2024-12-28T19:26:00Z
by OpenModelicaOpenModelica 1.24.3 using GenerateDoc.mos