Performance data for chiller model.
This data corresponds to the following EnergyPlus model:
Chiller:Electric:ReformulatedEIR,
ReformEIRChiller York YT 1266kW/4.39COP/Vanes, !- Name
1266000, !- Reference Capacity {W}
4.39, !- Reference COP {W/W}
5.56, !- Reference Leaving Chilled Water Temperature {C}
41.44, !- Reference Leaving Condenser Water Temperature {C}
0.03533, !- Reference Chilled Water Flow Rate {m3/s}
0.05773, !- Reference Condenser Water Flow Rate {m3/s}
ReformEIRChiller York YT 1266kW/4.39COP/Vanes CAPFT, !- Cooling Capacity Function of Temperature Curve Name
ReformEIRChiller York YT 1266kW/4.39COP/Vanes EIRFT, !- Electric Input to Cooling Output Ratio Function of Temperature Curve Name
ReformEIRChiller York YT 1266kW/4.39COP/Vanes EIRFPLR, !- Electric Input to Cooling Output Ratio Function of Part Load Ratio Curve Name
0.11, !- Minimum Part Load Ratio
1.05, !- Maximum Part Load Ratio
1.0, !- Optimum Part Load Ratio
0.11, !- Minimum Unloading Ratio
Chilled Water Side Inlet Node, !- Chilled Water Inlet Node Name
Chilled Water Side Outlet Node, !- Chilled Water Outlet Node Name
Condenser Side Inlet Node, !- Condenser Inlet Node Name
Condenser Side Outlet Node, !- Condenser Outlet Node Name
1.0, !- Compressor Motor Efficiency
2.0, !- Leaving Chilled Water Lower Temperature Limit {C}
ConstantFlow, !- Chiller Flow Mode Type
0.0; !- Design Heat Recovery Water Flow Rate {m3/s}
record ReformEIRChiller_York_YT_1266kW_4_39COP_Vanes = Buildings.Fluid.Chillers.Data.ElectricReformulatedEIR.Generic(QEva_flow_nominal = -1266000, COP_nominal = 4.39, PLRMin = 0.11, PLRMinUnl = 0.11, PLRMax = 1.05, mEva_flow_nominal = 1000*0.03533, mCon_flow_nominal = 1000*0.05773, TEvaLvg_nominal = 273.15 + 5.56, TConLvg_nominal = 273.15 + 41.44, TEvaLvgMin = 273.15 + 5.56, TEvaLvgMax = 273.15 + 8.89, TConLvgMin = 273.15 + 17.28, TConLvgMax = 273.15 + 42.31, capFunT = {1.556501E-03, -4.410896E-02, -1.854492E-03, 6.411584E-02, -1.204698E-03, 3.060359E-03}, EIRFunT = {1.265473E-01, 5.028662E-02, -4.704162E-03, 7.913033E-03, 3.096000E-04, -4.283498E-04}, EIRFunPLR = {1.253346E+00, -3.406609E-02, 1.893094E-04, 2.554443E-01, -1.655620E+00, 2.220865E-02, 0.000000E+00, 1.319681E+00, 0.000000E+00, 0.000000E+00}, etaMotor = 1.0);
Generated at 2024-12-28T19:26:00Z
by OpenModelicaOpenModelica 1.24.3 using GenerateDoc.mos