Performance data for chiller model.
This data corresponds to the following EnergyPlus model:
Chiller:Electric:ReformulatedEIR,
ReformEIRChiller York YT 1368kW/7.35COP/VSD, !- Name
1367900, !- Reference Capacity {W}
7.35, !- Reference COP {W/W}
5.56, !- Reference Leaving Chilled Water Temperature {C}
28.80, !- Reference Leaving Condenser Water Temperature {C}
0.05047, !- Reference Chilled Water Flow Rate {m3/s}
0.07571, !- Reference Condenser Water Flow Rate {m3/s}
ReformEIRChiller York YT 1368kW/7.35COP/VSD CAPFT, !- Cooling Capacity Function of Temperature Curve Name
ReformEIRChiller York YT 1368kW/7.35COP/VSD EIRFT, !- Electric Input to Cooling Output Ratio Function of Temperature Curve Name
ReformEIRChiller York YT 1368kW/7.35COP/VSD EIRFPLR, !- Electric Input to Cooling Output Ratio Function of Part Load Ratio Curve Name
0.10, !- Minimum Part Load Ratio
1.03, !- Maximum Part Load Ratio
1.0, !- Optimum Part Load Ratio
0.10, !- Minimum Unloading Ratio
Chilled Water Side Inlet Node, !- Chilled Water Inlet Node Name
Chilled Water Side Outlet Node, !- Chilled Water Outlet Node Name
Condenser Side Inlet Node, !- Condenser Inlet Node Name
Condenser Side Outlet Node, !- Condenser Outlet Node Name
1.0, !- Compressor Motor Efficiency
2.0, !- Leaving Chilled Water Lower Temperature Limit {C}
ConstantFlow, !- Chiller Flow Mode Type
0.0; !- Design Heat Recovery Water Flow Rate {m3/s}
record ReformEIRChiller_York_YT_1368kW_7_35COP_VSD = Buildings.Fluid.Chillers.Data.ElectricReformulatedEIR.Generic(QEva_flow_nominal = -1367900, COP_nominal = 7.35, PLRMin = 0.10, PLRMinUnl = 0.10, PLRMax = 1.03, mEva_flow_nominal = 1000*0.05047, mCon_flow_nominal = 1000*0.07571, TEvaLvg_nominal = 273.15 + 5.56, TConLvg_nominal = 273.15 + 28.80, TEvaLvgMin = 273.15 + 4.44, TEvaLvgMax = 273.15 + 8.89, TConLvgMin = 273.15 + 17.76, TConLvgMax = 273.15 + 34.51, capFunT = {-1.988920E-01, -1.019014E-01, -4.605586E-03, 1.364167E-01, -4.142785E-03, 8.790965E-03}, EIRFunT = {1.787713E-01, -1.943742E-02, -5.155001E-03, 4.314534E-02, -5.446713E-04, 2.049096E-03}, EIRFunPLR = {-4.466479E-01, 1.188856E-01, -5.385997E-05, -2.756308E+00, 4.709118E+00, -1.161211E-01, 0.000000E+00, -5.402852E-01, 0.000000E+00, 0.000000E+00}, etaMotor = 1.0);
Generated at 2024-11-22T19:25:38Z
by OpenModelicaOpenModelica 1.24.2 using GenerateDoc.mos