Performance data for chiller model.
This data corresponds to the following EnergyPlus model:
Chiller:Electric:ReformulatedEIR,
ReformEIRChiller York YT 1495kW/7.51COP/VSD, !- Name
1494500, !- Reference Capacity {W}
7.51, !- Reference COP {W/W}
7.22, !- Reference Leaving Chilled Water Temperature {C}
29.92, !- Reference Leaving Condenser Water Temperature {C}
0.0429, !- Reference Chilled Water Flow Rate {m3/s}
0.06719, !- Reference Condenser Water Flow Rate {m3/s}
ReformEIRChiller York YT 1495kW/7.51COP/VSD CAPFT, !- Cooling Capacity Function of Temperature Curve Name
ReformEIRChiller York YT 1495kW/7.51COP/VSD EIRFT, !- Electric Input to Cooling Output Ratio Function of Temperature Curve Name
ReformEIRChiller York YT 1495kW/7.51COP/VSD EIRFPLR, !- Electric Input to Cooling Output Ratio Function of Part Load Ratio Curve Name
0.11, !- Minimum Part Load Ratio
1.04, !- Maximum Part Load Ratio
1.0, !- Optimum Part Load Ratio
0.11, !- Minimum Unloading Ratio
Chilled Water Side Inlet Node, !- Chilled Water Inlet Node Name
Chilled Water Side Outlet Node, !- Chilled Water Outlet Node Name
Condenser Side Inlet Node, !- Condenser Inlet Node Name
Condenser Side Outlet Node, !- Condenser Outlet Node Name
1.0, !- Compressor Motor Efficiency
2.0, !- Leaving Chilled Water Lower Temperature Limit {C}
ConstantFlow, !- Chiller Flow Mode Type
0.0; !- Design Heat Recovery Water Flow Rate {m3/s}
record ReformEIRChiller_York_YT_1495kW_7_51COP_VSD = Buildings.Fluid.Chillers.Data.ElectricReformulatedEIR.Generic(QEva_flow_nominal = -1494500, COP_nominal = 7.51, PLRMin = 0.11, PLRMinUnl = 0.11, PLRMax = 1.04, mEva_flow_nominal = 1000*0.0429, mCon_flow_nominal = 1000*0.06719, TEvaLvg_nominal = 273.15 + 7.22, TConLvg_nominal = 273.15 + 29.92, TEvaLvgMin = 273.15 + 5.56, TEvaLvgMax = 273.15 + 8.89, TConLvgMin = 273.15 + 18.69, TConLvgMax = 273.15 + 41.38, capFunT = {6.015487E-01, -1.630120E-01, 9.951930E-03, 7.452875E-02, -1.608224E-03, 2.001891E-03}, EIRFunT = {1.954138E-01, -1.627980E-01, 5.924232E-03, 8.194832E-02, -8.723337E-04, 7.443855E-04}, EIRFunPLR = {6.377828E-01, -3.620643E-02, -1.187858E-04, 5.832958E-01, -9.230655E-01, 4.307256E-02, 0.000000E+00, 6.079021E-01, 0.000000E+00, 0.000000E+00}, etaMotor = 1.0);
Generated at 2024-11-22T19:25:38Z
by OpenModelicaOpenModelica 1.24.2 using GenerateDoc.mos