Performance data for chiller model.
This data corresponds to the following EnergyPlus model:
Chiller:Electric:ReformulatedEIR,
ReformEIRChiller York YT 1758kW/6.26COP/Vanes, !- Name
1758300, !- Reference Capacity {W}
6.26, !- Reference COP {W/W}
5.56, !- Reference Leaving Chilled Water Temperature {C}
32.18, !- Reference Leaving Condenser Water Temperature {C}
0.06309, !- Reference Chilled Water Flow Rate {m3/s}
0.06309, !- Reference Condenser Water Flow Rate {m3/s}
ReformEIRChiller York YT 1758kW/6.26COP/Vanes CAPFT, !- Cooling Capacity Function of Temperature Curve Name
ReformEIRChiller York YT 1758kW/6.26COP/Vanes EIRFT, !- Electric Input to Cooling Output Ratio Function of Temperature Curve Name
ReformEIRChiller York YT 1758kW/6.26COP/Vanes EIRFPLR, !- Electric Input to Cooling Output Ratio Function of Part Load Ratio Curve Name
0.10, !- Minimum Part Load Ratio
1.16, !- Maximum Part Load Ratio
1.0, !- Optimum Part Load Ratio
0.10, !- Minimum Unloading Ratio
Chilled Water Side Inlet Node, !- Chilled Water Inlet Node Name
Chilled Water Side Outlet Node, !- Chilled Water Outlet Node Name
Condenser Side Inlet Node, !- Condenser Inlet Node Name
Condenser Side Outlet Node, !- Condenser Outlet Node Name
1.0, !- Compressor Motor Efficiency
2.0, !- Leaving Chilled Water Lower Temperature Limit {C}
ConstantFlow, !- Chiller Flow Mode Type
0.0; !- Design Heat Recovery Water Flow Rate {m3/s}
record ReformEIRChiller_York_YT_1758kW_6_26COP_Vanes = Buildings.Fluid.Chillers.Data.ElectricReformulatedEIR.Generic(QEva_flow_nominal = -1758300, COP_nominal = 6.26, PLRMin = 0.10, PLRMinUnl = 0.10, PLRMax = 1.16, mEva_flow_nominal = 1000*0.06309, mCon_flow_nominal = 1000*0.06309, TEvaLvg_nominal = 273.15 + 5.56, TConLvg_nominal = 273.15 + 32.18, TEvaLvgMin = 273.15 + 5.56, TEvaLvgMax = 273.15 + 10.00, TConLvgMin = 273.15 + 21.48, TConLvgMax = 273.15 + 33.76, capFunT = {4.841919E-01, -2.437152E-02, 3.244522E-03, 5.590357E-02, -1.302819E-03, 9.257097E-04}, EIRFunT = {1.729452E-01, 9.227136E-02, -5.580943E-03, 1.946191E-02, 3.155080E-05, -7.904242E-04}, EIRFunPLR = {9.471258E-01, -4.669457E-02, -4.461248E-04, 5.587776E-02, 6.578054E-01, 7.103286E-02, 0.000000E+00, -9.855688E-01, 0.000000E+00, 0.000000E+00}, etaMotor = 1.0);
Generated at 2024-12-28T19:26:00Z
by OpenModelicaOpenModelica 1.24.3 using GenerateDoc.mos