Performance data for chiller model.
This data corresponds to the following EnergyPlus model:
Chiller:Electric:ReformulatedEIR,
ReformEIRChiller York YT 1758kW/6.28COP/Vanes, !- Name
1758300, !- Reference Capacity {W}
6.28, !- Reference COP {W/W}
6.67, !- Reference Leaving Chilled Water Temperature {C}
34.60, !- Reference Leaving Condenser Water Temperature {C}
0.07571, !- Reference Chilled Water Flow Rate {m3/s}
0.09464, !- Reference Condenser Water Flow Rate {m3/s}
ReformEIRChiller York YT 1758kW/6.28COP/Vanes CAPFT, !- Cooling Capacity Function of Temperature Curve Name
ReformEIRChiller York YT 1758kW/6.28COP/Vanes EIRFT, !- Electric Input to Cooling Output Ratio Function of Temperature Curve Name
ReformEIRChiller York YT 1758kW/6.28COP/Vanes EIRFPLR, !- Electric Input to Cooling Output Ratio Function of Part Load Ratio Curve Name
0.20, !- Minimum Part Load Ratio
1.06, !- Maximum Part Load Ratio
1.0, !- Optimum Part Load Ratio
0.20, !- Minimum Unloading Ratio
Chilled Water Side Inlet Node, !- Chilled Water Inlet Node Name
Chilled Water Side Outlet Node, !- Chilled Water Outlet Node Name
Condenser Side Inlet Node, !- Condenser Inlet Node Name
Condenser Side Outlet Node, !- Condenser Outlet Node Name
1.0, !- Compressor Motor Efficiency
2.0, !- Leaving Chilled Water Lower Temperature Limit {C}
ConstantFlow, !- Chiller Flow Mode Type
0.0; !- Design Heat Recovery Water Flow Rate {m3/s}
record ReformEIRChiller_York_YT_1758kW_6_28COP_Vanes = Buildings.Fluid.Chillers.Data.ElectricReformulatedEIR.Generic(QEva_flow_nominal = -1758300, COP_nominal = 6.28, PLRMin = 0.20, PLRMinUnl = 0.20, PLRMax = 1.06, mEva_flow_nominal = 1000*0.07571, mCon_flow_nominal = 1000*0.09464, TEvaLvg_nominal = 273.15 + 6.67, TConLvg_nominal = 273.15 + 34.60, TEvaLvgMin = 273.15 + 4.44, TEvaLvgMax = 273.15 + 8.89, TConLvgMin = 273.15 + 20.46, TConLvgMax = 273.15 + 39.72, capFunT = {5.062633E-01, -9.373882E-03, -2.822764E-03, 4.202164E-02, -1.092132E-03, 2.074549E-03}, EIRFunT = {5.699849E-01, -9.813327E-03, 4.223116E-04, 4.842283E-03, 4.078201E-04, -7.615896E-04}, EIRFunPLR = {2.911331E-01, -4.317969E-03, 1.448369E-05, 6.226793E-01, 7.992053E-02, 3.393326E-03, 0.000000E+00, 1.919540E-02, 0.000000E+00, 0.000000E+00}, etaMotor = 1.0);
Generated at 2024-12-28T19:26:00Z
by OpenModelicaOpenModelica 1.24.3 using GenerateDoc.mos