Performance data for chiller model.
This data corresponds to the following EnergyPlus model:
Chiller:Electric:ReformulatedEIR,
ReformEIRChiller York YT 1794kW/8.11COP/Vanes, !- Name
1793500, !- Reference Capacity {W}
8.11, !- Reference COP {W/W}
7.22, !- Reference Leaving Chilled Water Temperature {C}
28.88, !- Reference Leaving Condenser Water Temperature {C}
0.05148, !- Reference Chilled Water Flow Rate {m3/s}
0.09653, !- Reference Condenser Water Flow Rate {m3/s}
ReformEIRChiller York YT 1794kW/8.11COP/Vanes CAPFT, !- Cooling Capacity Function of Temperature Curve Name
ReformEIRChiller York YT 1794kW/8.11COP/Vanes EIRFT, !- Electric Input to Cooling Output Ratio Function of Temperature Curve Name
ReformEIRChiller York YT 1794kW/8.11COP/Vanes EIRFPLR, !- Electric Input to Cooling Output Ratio Function of Part Load Ratio Curve Name
0.10, !- Minimum Part Load Ratio
1.08, !- Maximum Part Load Ratio
1.0, !- Optimum Part Load Ratio
0.10, !- Minimum Unloading Ratio
Chilled Water Side Inlet Node, !- Chilled Water Inlet Node Name
Chilled Water Side Outlet Node, !- Chilled Water Outlet Node Name
Condenser Side Inlet Node, !- Condenser Inlet Node Name
Condenser Side Outlet Node, !- Condenser Outlet Node Name
1.0, !- Compressor Motor Efficiency
2.0, !- Leaving Chilled Water Lower Temperature Limit {C}
ConstantFlow, !- Chiller Flow Mode Type
0.0; !- Design Heat Recovery Water Flow Rate {m3/s}
record ReformEIRChiller_York_YT_1794kW_8_11COP_Vanes = Buildings.Fluid.Chillers.Data.ElectricReformulatedEIR.Generic(QEva_flow_nominal = -1793500, COP_nominal = 8.11, PLRMin = 0.10, PLRMinUnl = 0.10, PLRMax = 1.08, mEva_flow_nominal = 1000*0.05148, mCon_flow_nominal = 1000*0.09653, TEvaLvg_nominal = 273.15 + 7.22, TConLvg_nominal = 273.15 + 28.88, TEvaLvgMin = 273.15 + 5.56, TEvaLvgMax = 273.15 + 8.89, TConLvgMin = 273.15 + 18.71, TConLvgMax = 273.15 + 34.34, capFunT = {1.475615E+00, -2.480005E-01, 1.353388E-02, 5.216264E-02, -2.330109E-03, 5.131852E-03}, EIRFunT = {1.190864E+00, 3.400270E-01, -8.717000E-03, -1.107704E-01, 3.433891E-03, -8.538300E-03}, EIRFunPLR = {-9.081317E-02, 1.524614E-02, 8.256304E-04, -6.921348E-01, 4.110008E+00, -6.003188E-02, 0.000000E+00, -1.751625E+00, 0.000000E+00, 0.000000E+00}, etaMotor = 1.0);
Generated at 2024-12-28T19:26:00Z
by OpenModelicaOpenModelica 1.24.3 using GenerateDoc.mos