Performance data for chiller model.
This data corresponds to the following EnergyPlus model:
Chiller:Electric:ReformulatedEIR,
ReformEIRChiller York YT 3133kW/9.16COP/Vanes, !- Name
3133300, !- Reference Capacity {W}
9.16, !- Reference COP {W/W}
5.56, !- Reference Leaving Chilled Water Temperature {C}
19.37, !- Reference Leaving Condenser Water Temperature {C}
0.08076, !- Reference Chilled Water Flow Rate {m3/s}
0.12618, !- Reference Condenser Water Flow Rate {m3/s}
ReformEIRChiller York YT 3133kW/9.16COP/Vanes CAPFT, !- Cooling Capacity Function of Temperature Curve Name
ReformEIRChiller York YT 3133kW/9.16COP/Vanes EIRFT, !- Electric Input to Cooling Output Ratio Function of Temperature Curve Name
ReformEIRChiller York YT 3133kW/9.16COP/Vanes EIRFPLR, !- Electric Input to Cooling Output Ratio Function of Part Load Ratio Curve Name
0.07, !- Minimum Part Load Ratio
1.04, !- Maximum Part Load Ratio
1.0, !- Optimum Part Load Ratio
0.07, !- Minimum Unloading Ratio
Chilled Water Side Inlet Node, !- Chilled Water Inlet Node Name
Chilled Water Side Outlet Node, !- Chilled Water Outlet Node Name
Condenser Side Inlet Node, !- Condenser Inlet Node Name
Condenser Side Outlet Node, !- Condenser Outlet Node Name
1.0, !- Compressor Motor Efficiency
2.0, !- Leaving Chilled Water Lower Temperature Limit {C}
ConstantFlow, !- Chiller Flow Mode Type
0.0; !- Design Heat Recovery Water Flow Rate {m3/s}
record ReformEIRChiller_York_YT_3133kW_9_16COP_Vanes = Buildings.Fluid.Chillers.Data.ElectricReformulatedEIR.Generic(QEva_flow_nominal = -3133300, COP_nominal = 9.16, PLRMin = 0.07, PLRMinUnl = 0.07, PLRMax = 1.04, mEva_flow_nominal = 1000*0.08076, mCon_flow_nominal = 1000*0.12618, TEvaLvg_nominal = 273.15 + 5.56, TConLvg_nominal = 273.15 + 19.37, TEvaLvgMin = 273.15 + 5.56, TEvaLvgMax = 273.15 + 8.89, TConLvgMin = 273.15 + 19.37, TConLvgMax = 273.15 + 35.91, capFunT = {6.112157E-01, -1.430728E-02, 9.823748E-05, 3.293543E-02, -1.221859E-03, 2.659301E-03}, EIRFunT = {8.749714E-01, -2.881975E-02, 2.003695E-03, 7.313755E-03, 5.578288E-04, -1.170615E-03}, EIRFunPLR = {3.389568E-01, -1.864923E-02, 3.548361E-04, 1.107404E+00, -5.912797E-01, -4.559304E-04, 0.000000E+00, 3.910858E-01, 0.000000E+00, 0.000000E+00}, etaMotor = 1.0);
Generated at 2024-12-28T19:26:00Z
by OpenModelicaOpenModelica 1.24.3 using GenerateDoc.mos