| Movers.Data.Generic | perPum | | |
| Configuration |
| Boolean | use_siz | true | Set to true for built-in sizing of control valve and optional pump |
| Boolean | use_dp1 | | Set to true to enable dp1_nominal |
| Boolean | use_dp2 | | Set to true to enable dp2_nominal |
| Buildings.Fluid.HydronicConfigurations.Types.Valve | typVal | | Type of control valve |
| Boolean | have_typVar | true | Set to true to enable the choice of the controlled variable |
| Nominal condition |
| Modelica.Units.SI.MassFlowRate | m1_flow_nominal | | Mass flow rate in primary circuit at design conditions |
| Modelica.Units.SI.MassFlowRate | m2_flow_nominal | | Mass flow rate in consumer circuit at design conditions |
| Modelica.Units.SI.PressureDifference | dp1_nominal | | Primary circuit pressure differential at design conditions |
| Modelica.Units.SI.PressureDifference | dp2_nominal | | Consumer circuit pressure differential at design conditions |
| Control valve |
| Buildings.Fluid.HydronicConfigurations.Types.ValveCharacteristic | typCha | Buildings.Fluid.HydronicConfigurations.Types.ValveCharacteristic.EqualPercentage | Control valve characteristic |
| Modelica.Units.SI.PressureDifference | dpValve_nominal | | Control valve pressure drop at design conditions |
| Actuators.Valves.Data.Generic | flowCharacteristics | | Table with flow characteristics |
| Actuators.Valves.Data.Generic | flowCharacteristics1 | | Table with flow characteristics for direct flow path at port_1 |
| Actuators.Valves.Data.Generic | flowCharacteristics3 | | Table with flow characteristics for bypass flow path at port_3 |
| Pump |
| Buildings.Fluid.HydronicConfigurations.Types.Pump | typPum | Buildings.Fluid.HydronicConfigurations.Types.Pump.VariableInput | Type of secondary pump |
| Buildings.Fluid.HydronicConfigurations.Types.PumpModel | typPumMod | Buildings.Fluid.HydronicConfigurations.Types.PumpModel.Speed | Type of pump model |
| Modelica.Units.SI.MassFlowRate | mPum_flow_nominal | m2_flow_nominal | Pump head at design conditions |
| Modelica.Units.SI.PressureDifference | dpPum_nominal | dp2_nominal + dpBal2_nominal | Pump head at design conditions |
| Controls |
| Buildings.Fluid.HydronicConfigurations.Types.Control | typCtl | Buildings.Fluid.HydronicConfigurations.Types.Control.None | Type of built-in controls |
| Buildings.Fluid.HydronicConfigurations.Types.ControlVariable | typVar | Buildings.Fluid.HydronicConfigurations.Types.ControlVariable.SupplyTemperature | Controlled variable |
| Buildings.Controls.OBC.CDL.Types.SimpleController | controllerType | Buildings.Controls.OBC.CDL.Types.SimpleController.PI | Type of controller |
| Real | k | 0.1 | Gain of controller |
| Real | Ti | 120 | Time constant of integrator block |
| Assumptions |
| Boolean | use_lumFloRes | true | Set to true to use a lumped flow resistance when possible |
| Boolean | allowFlowReversal | true | = false to simplify equations, assuming, but not enforcing, no flow reversal for medium 1 |
| Balancing valves |
| Modelica.Units.SI.PressureDifference | dpBal1_nominal | 0 | Primary balancing valve pressure drop at design conditions |
| Modelica.Units.SI.PressureDifference | dpBal2_nominal | 0 | Secondary balancing valve pressure drop at design conditions |
| Modelica.Units.SI.PressureDifference | dpBal3_nominal | 0 | Bypass balancing valve pressure drop at design conditions |
| Dynamics › Conservation equations |
| Modelica.Fluid.Types.Dynamics | energyDynamics | Modelica.Fluid.Types.Dynamics.FixedInitial | Type of energy balance: dynamic (3 initialization options) or steady state |
| Advanced › Diagnostics |
| Boolean | show_T | false | = true, if actual temperature at port is computed |
Medium